Hej,
Då jag glömt bort PIN så återställde jag Ledgern m.h.a. 24-ords-frasen.
Laddade ner programvara till datorn och följde instruktionen steg för steg.
Emellertid så visar programmet att stickan inte innehåller några BTC, vilket är fel.
Någon som har en klok tanke om detta?
Steg som följts:
Då jag glömt bort PIN så återställde jag Ledgern m.h.a. 24-ords-frasen.
Laddade ner programvara till datorn och följde instruktionen steg för steg.
Emellertid så visar programmet att stickan inte innehåller några BTC, vilket är fel.
Någon som har en klok tanke om detta?
Steg som följts:
Start restoration
1. Connect the Ledger Nano S to your computer using the micro USB/USB cable.
2. Press both buttons simultaneously as instructed on the device.
3. Press the left button located above the cancel icon when asked Configure as new
device?
4. Press the right button located above the validation icon to select Restore a
configuration?
Choose a PIN code
The length of the required PIN code varies:
● Firmware version 1.3 or higher requires a PIN code between 4 and 8 digits long;
● Firmware version 1.2 or lower requires a 4-digit PIN code.
To set your PIN code:
1. Press both buttons when Choose a PIN code is shown on the device.
2. Press the right or left button to choose the first digit of your PIN code.
3. Press both buttons to select the digit.
4. Repeat the process until all digits of your PIN code are selected.
5. Select the check icon (✓) and press both buttons to enter the PIN code.
6. Enter the PIN code again to confirm.
7.
Enter recovery phrase
1. Press the right button to choose the length of your recovery phrase (12, 18 or 24 words). Press both buttons to enter.
2. Choose the first letter of Word #1 by pressing the right or left button. Press both buttons to select the letter.
3. Select the second letter of Word #1. Repeat until the device shows suggested words to choose from.
4. Choose Word #1 from the suggested words. Press both buttons to select it.
5. Repeat the process for each word of your recovery phrase.
6. Your device is now ready is displayed if you've successfully entered your recovery
phrase.
1. Connect the Ledger Nano S to your computer using the micro USB/USB cable.
2. Press both buttons simultaneously as instructed on the device.
3. Press the left button located above the cancel icon when asked Configure as new
device?
4. Press the right button located above the validation icon to select Restore a
configuration?
Choose a PIN code
The length of the required PIN code varies:
● Firmware version 1.3 or higher requires a PIN code between 4 and 8 digits long;
● Firmware version 1.2 or lower requires a 4-digit PIN code.
To set your PIN code:
1. Press both buttons when Choose a PIN code is shown on the device.
2. Press the right or left button to choose the first digit of your PIN code.
3. Press both buttons to select the digit.
4. Repeat the process until all digits of your PIN code are selected.
5. Select the check icon (✓) and press both buttons to enter the PIN code.
6. Enter the PIN code again to confirm.
7.
Enter recovery phrase
1. Press the right button to choose the length of your recovery phrase (12, 18 or 24 words). Press both buttons to enter.
2. Choose the first letter of Word #1 by pressing the right or left button. Press both buttons to select the letter.
3. Select the second letter of Word #1. Repeat until the device shows suggested words to choose from.
4. Choose Word #1 from the suggested words. Press both buttons to select it.
5. Repeat the process for each word of your recovery phrase.
6. Your device is now ready is displayed if you've successfully entered your recovery
phrase.
